Search found 239 matches

by Allen K
Sat Aug 15, 2015 7:27 am
Forum: Claw and Order
Topic: Hollycrane
Replies: 8
Views: 1615

Re: Hollycrane

Good luck! :)
by Allen K
Thu Aug 13, 2015 12:14 pm
Forum: Claw and Order
Topic: Hollycrane
Replies: 8
Views: 1615

Re: Hollycrane

Not really sure how easy it would be. You'd have to find a complete set of parts from another machine, but make sure that they would fit into your cabinet. The width of the track between the rails would have to match the width of the gantry. I lucked out that the Grayhound gantry was exactly the sam...
by Allen K
Sun Aug 09, 2015 9:23 pm
Forum: Claw and Order
Topic: Hollycrane
Replies: 8
Views: 1615

Re: Hollycrane

Sorry, I don't know if you'd have any luck getting it to work, considering parts for these machines are pretty much impossible to find. I bought two machines very similar to this one on Ebay a few years ago and had to remove all parts from the cabinet and replace with parts from a more modern machin...
by Allen K
Sun Aug 09, 2015 9:19 pm
Forum: Claw and Order
Topic: Rigged crane machines
Replies: 1
Views: 682

Re: Rigged crane machines

On most machines you can either set a fixed strength that's always the same (if owner is greedy, they can set it to be too weak for the prizes in the machine), or it can be set to a certain payout rate, so depending on the cost of the prizes, you might have to play 10 times to get a full strength, o...
by Allen K
Mon Jun 29, 2015 11:54 pm
Forum: Claw and Order
Topic: new to claw machine ownership
Replies: 1
Views: 658

Re: new to claw machine ownership

Welcome! That's a tough one to diagnose. Are you able to post a picture of what the machine looks like? That might help figure out what machine it is and if there are any manuals available.

Thanks!

Allen K
BeTheClaw.com
by Allen K
Wed Jun 24, 2015 12:45 pm
Forum: Claw and Order
Topic: Greyhound skill crane issue
Replies: 2
Views: 4481

Re: Greyhound skill crane issue

Hi there, Does the display change numbers when you first turn it on? It typically shows the date of the firmware. It sounds like either the left limit switch is bad (the switch that gets pressed when the claw comes all the way to the left), or there's a problem with the CPU board that would need to ...
by Allen K
Wed Jun 10, 2015 12:35 pm
Forum: Claw and Order
Topic: Claw machines for sale?
Replies: 4
Views: 1326

Re: Claw machines for sale?

You might want to mention where you live :)


Allen K
by Allen K
Wed Jun 10, 2015 12:34 pm
Forum: Claw and Order
Topic: Greyhound Skill Crane - Help
Replies: 1
Views: 676

Re: Greyhound Skill Crane - Help

Hi there, That kind of erratic behavior is usually an indication of a problem with one of the boards (CPU likely in this case). That's not something you could fix yourself, so I would suggest to check www.aslex.net. This site is owned by a former Grayhound technician (Scott). Give him a call and he ...
by Allen K
Wed Jun 10, 2015 12:28 pm
Forum: Claw and Order
Topic: In Need of a Skill Crane Manual
Replies: 1
Views: 1227

Re: In Need of a Skill Crane Manual

Jake - for what machine, specifically?


Allen K
by Allen K
Tue May 12, 2015 3:39 pm
Forum: Claw and Order
Topic: Where can I get 30ohm coil for elaut candy claw machine.
Replies: 1
Views: 914

Re: Where can I get 30ohm coil for elaut candy claw machine.

http://elautparts.com is a resource, but parts from manufacturers are insanely overpriced. I'm not sure that you'll be able to find a magnet specifically for you machine elsewhere, so you'd probably want to measure your claw cylinder and search by size / voltage / ohm rating at a place such as http:...